Variasi Frekuensi pada Electric Rotary Table Berbasis Inverter Guna Menurunkan Cycle Time dan Cacat Produk pada Pengelasan Pipa Kapiler
Abstract
Abstract
Cycle Time is a matter that must be considered in production time, a good Cycle Time will support the targets that must be met, even if Cycle Time decreases, production will also increase and company turnover will also Increase. In the case study of PT Arisamandiri Pratama, one of its productions is in the form of AC parts, namely capillary pipes which still use a manual rotating table to rotate the pipe to be welded so that it is unable to reach the target of 800 parts / hour with an average Not Good product of 93 parts / day. The design of an inverter-based electric rotary table can reduce cycle time, but how much frequency will affect the results of a welding, not that the faster the welding process the better, the faster the welding will affect the vibration of the table machine which will have an impact on the welding results. By experiment the inverter frequency setting is expected to get a frequency value with maximum speed but no vibration on the rotation table, the frequency used is between 700 Hz to 1500 Hz with an interval of 100 Hz. The experimental results show that the best frequency is 1000 Hz, with a rotation speed of 16 rpm with a production capacity of 935 parts / hour with Not Good products of 59 parts / day or a decrease in Not Good products by 42.1% per day
Keywords
Full Text:
PDFReferences
Abidin, Zainal ; Priangkoso, T. ; D., Pengujian Performance Motor Listrik Ac 3 Fasa Dengan Daya 3 Hp Menggunakan Pembebanan Generator Listrik. Jurnal Momentum 2019; 9 No 1(ISSN 0216-7395), 30–34.
Alwarits, Daswarman, & Nasir, M., Pengaruh Media Pendingin pada Proses Hardening terhadap Peningkatan Kekerasan Baja Karbon Sedang. Automotive Engineering Education Journals. 2014; 3 No 4(e-ISSN:2302-335X), 1–5.
Andreansyah, R., Perencanaan Dan Pembuatan Rangkaian Daya Starting Motor 3 Fasa ,380 Volt ,50 Hz, 3 Hp Dengan Metoda Bintang (Y) – Segitiga (∆). Cyclotron,. 2019; 2 No 1(P-ISSN: 2614-5499,E-ISSN: 2614-5164), 6–12.
Cross, N., Engineering Design Methods. In The Open University (Fourth). 2000. The Open University.
Danuri, R., Perancangan Alat Perajang Serbaguna Tipe Blade Sliding Dengan Menggunakan Prinsip Mechanical Ralph Steiner. Paper Knowledge . Toward a Media History of Documents. 2015; 3 No 1(ISSN: 2087-3832), 26–30.
Juhana., Analisa Pengaruh Beban Linier Dan Beban Non Linier Terhadap Fungsi Kerja Miniature Circuit Breaker. Journal Of Electrical Power, Instrumentation and Control (EPIC). 2018; 1 No 1(e-ISSN: 2614-8595, p-ISSN: 2615-0646), 13–23.
Kamajaya, K., Fisika Untuk SMU. 2003. Grafindo Media Pratama.
Kanniga, E., Selvaramarathnam, K., & Sundararajan, M., Embedded control using mems sensor with voice command and CCTV camera. Indian Journal of Science and Technology. 2013; 6(e-ISSN: 0974-5645,p-ISSN: 0974-6846), 4794–4796.
Kurniawan, I., Girawan, B. A., & Fitriyani, I.,Rancang Bangun Alat Bantu Las Meja Putar. Bangun Rekaprima. 2020; 06 No 1, 1–14.
Kurniawan, Y., & Zulkifli, Z., Rancang Bangun Pembangkit Listrik Menggunakan Solenoida Dengan Pemanfaatan Fluks Magnet. RELE (Rekayasa Elektrikal Dan Energi). 2019; 2 No 1(ISSN: 2622 – 7002), 9–13.
Munawir, Turmizi, & A., Analisa Kegagalan Poros Pompa Sentrifugal Ebara Type 56-GA 4002 A Melalui Evaliasi Pola Patahan Serta Pengujian Kekerasan dan Metalografi. Mesin Sains Terapan. 2019; 3 No 2(e-ISSN: 2597-9140), 81–87.
Oladapo, B. I., Balogun, V. A., Adeoye, A. O. M., Ijagbemi, C. O., Oluwole, A. S., Daniyan, I. A., Esoso Aghor, A., & Simeon, A. P., Model design and simulation of automatic sorting machine using proximity sensor. Engineering Science and Technology, an International Journal. 2016; 19(ISSN: 2215-0986), 1452–1456.
Pachal, D.; Tambe, M.; Pachal, H., No Title. International Journal of Emerging Technology and Advanced Engineering. 2016; 2 No 8(e-ISSN: 2597-9140), 81–87.
Prasetyo, E., Dahlan, D., & Ryfaldi, R., Analisis Uji Jalan Sepeda Motor Listrik 1 kW. Seminar Rekayasa Teknologi. 2018; 53(e-ISSN : 2621-5934,p-ISSN : 2621-7112), 199–208.
R.S Khurmi ; J.K. Gupta., A Text Book Machine Design. Eurasia Publishing House(PVT.). 2018. LTD.
Sanda., Perancangan Mekanik Penggerak Batang Kendali Reaktor Riset. Jurnal Perangkat Nuklir. 2013; 3 No 5(ISSN: 1978-3515), 1–6.
Saptono, Hery ; Pramono, Gatot Eka ; Khind, H. Al., Analisa Daya Dan Kontrol Kecepatan Motor Pada Alat Bantu Las Rotary Positioner Table. Program Studi Teknik Mesin Fakultas Teknik,Universitas Ibn Khaldun Bogor, 2013; 4 No 1(ISSN: 2460-3988, e-ISSN: 2581-0979), 23–33.
Saputro, F. A., Yudo, H., & M., Studi Perhitungan Respon Struktur Pondasi Mesin Kapal Penyeberangan 1000 GT Akibat Pembebanan Statis. Jurnal Teknik Perkapalan. 2020; 8 no 2, 167–174.
Syah, F. I., & R, S. D. W., Eddy Current Untuk Pengujian Motor Bakar. Jurnal Sains Dan Teknologi (Sainteknol). 2018; 16 No 1(ISSN: 0216-4566), 33–44.
Vitting, A., Janß, A., Strathen, B., Strake, M., & Radermacher, K., Further development and evaluation of a universal foot switch for diverse medical disciplines within the framework of an open integration concept for the operation theatre of the future. Advances in Intelligent Systems and Computing. 2018; 590(e-ISBN: 978-3-319-60483-1,p-ISBN: 978-3-319-60482-4),
Wiryosumarto; Harsono; T.Okumura., Teknologi Pengelasan Logam. 2008; PT Balai Pustaka.
Yanto, Budi, Perencanaan dan analisis meja las untuk proses perbaikan Bottom Core pada molding pelek di PT Pakoakuina, Skripsi Universitas Negeri Jakarta. 2015.
DOI: http://dx.doi.org/10.32497/jrm.v18i3.5082
Refbacks
- There are currently no refbacks.
Copyright (c) 2023 Jurnal Rekayasa Mesin
_____________________________________________________________________
| Publisher: Mechanical Engineering Department, Politeknik Negeri Semarang (Semarang State Polytechnic) |
1.png){kind=logo}
_____________________________________________________________________
This work is licensed under a License Creative Commons Attribution-NonCommercial-ShareAlike 4.0 Internasional.