The Effect of Shot Peening Hardening Treatment on Pressure Variation on Mechanical Properties and Microstructure of S45C Steel
Abstract
The purpose of the study was to determine the mechanical properties and microstructure of S45C steel with automatic shot peening treatment. S45C steel is classified as medium steel with a carbon content of 0.51%. Variations of shot peening treatment with varying pressures of 5 bar, 6 bar, and 7 bar. Steel ball shooting uses a size of 0.8 mm, a distance of 100 mm, and a shooting angle of 90o. Hardness test using Vickers and microstructure observation using a microscope. The results of the average hardness test at a pressure of 5 bar are 193.3 VHN, at a pressure of 6 bar with a hardness of 227.2 VHN, and 7 bar with a hardness of 250 VHN. So it can be concluded that the higher the pressure used, the higher the level of hardness obtained. The results of the microstructute photo shown that the higher the pressure released, the more a structure with more martensite phases will be obtained, this has a direct relationship with the hardness of S45C steel.
Keywords
Full Text:
PDFReferences
References
. Abbas, H., & Aminy, A. Y. February). The effects of shielded metal arc welding (smaw) welding on the mechanical characteristics with heating treatment inn S45c steel. In Journal of Physics: Conference Series IOP Publishing ., vol. 962, no. 1, pp. 1-8, 2018, doi :10.1088/1742-6596/ 962/1/012063.
. Liu, C., Zheng, H., Gu, X., Jiang, B., & Liang, J. Effect of severe shot peening on corrosion behavior of AZ31 and
AZ91 magnesium alloys. Journal of Alloys and Compounds, vol.770, pp. 500-506, 2019.
. Bagherifard, S., Fernandez-Pariente, I., Ghelichi, R., & Guagliano, M. Fatigue behavior of notched steel specimens
with nanocrystallized surface obtained by severe shot peening. Materials & Design, vol. 45, pp. 497-503, 2013.
. Sivasankaran, S., Sivaprasad, K., Narayanasamy, R., & Satyanarayana, P. V. (2011). X-ray peak broadening analysis
of AA 6061100− x− x wt.% Al2O3 nanocomposite prepared by mechanical alloying. Materials Characterization,
vol. 62, no. 7, pp. 661-672.
. Maleki, E., & Unal, O. (2018). Roles of surface coverage increase and re-peening on properties of AISI 1045 carbon
steel in conventional and severe shot peening processes. Surfaces and Interfaces, vol. 11, pp. 82-90, 2018.
. Kato, H., & Yasunaga, K. Ultra-Fine and Nano-Crystalline Structure Induced by Sliding Friction of Carbon Steel.
In Defect and Diffusion Forum, vol. 382, pp. 63-67, 2018. Trans Tech Publications Ltd. doi.org/10.4028/www.
scientific.net/DDF.382.63.
. Mohamed, A. M. O., Farhat, Z., Warkentin, A., & Gillis, J. Effect of a moving automated shot peening and peening
parameters on surface integrity of Low carbon steel. Journal of Materials Processing Technology, vol. 277, 2020.
doi.org/10.1016/j.jmatprotec.2019.116399.
. Wibowo, T. N., Hartono, H., & Sugiantoro, B. Optimasi Parameter Gravitasi Shot Peening Terhadap Kekasaran,
Kekerasan dan Struktur Mikro ST 45 dengan Metode Taguchi. Infotekmesin, vol. 12, no. 1, pp.28-35, 2020.
. Yang, Z., Zheng, J., Zhan, K., Jiang, C., & Ji, V. Surface characteristic and wear resistance of S960 high-strength
steel after shot peening combing with ultrasonic sprayed graphene oxide coating. Journal of Materials Research and
Technology, vol.18, pp. 978-989, 2022. doi.org/10.1016/j.jmrt.2022.02.124
. Pratama, A. E., Sakuri, S., & Prabowo, N. R,Pengaruh Variasi Tekanan Gravity Shot Peening Pada Proses
Pengerasan Permukaan terhadap Sifat Mekanis dan Morfologi Struktur Baja S45C. Jurnal Flywheel, vol. 13, no. 2,
pp. 46-52. ,2022, doi.org/10.36040/ flywheel.v13i2.5688.
. Li, J., Yang, K., Guo, X., Huang, W., Wang, T., Guo, Y., & Fu, H. Structural design and parameter optimization on
a waste valve for hydraulic ram pumps. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of
Power and Energy, vol. 235, no.4, pp. 747-765, 2021.doi.org/10.1177/0957650920967489.
. Maliwemu, E. U. K., Malau, V., & Iswanto, P. T. Effect of shot peening in different shot distance and shot angle on
surface morphology, surface roughness and surface hardness of 316L biomaterial. In IOP Conference Series:
Materials Science and Engineering, vol. 299, no. 1, pp. 1 - 7 , 2018. Doi: 10.1088/1757-899X/299/1/012051.
. Wang, J., Lu, Y., Zhou, D., Sun, L., Xie, L., & Wang, J. Mechanical properties and microstructural response of
A14 aluminum alloy subjected to multiple laser shock peening impacts. Vacuum, vol. 165, pp. 193-198, 2019.
doi.org/10.1016/j.vacuum. 2019.03.058.
. Fu, W., Huang, Y., Sun, J., & Ngan, A. H. Strengthening CrFeCoNiMn0. 75Cu0. 25 high entropy alloy via laser
shock peening. International Journal of Plasticity, vol. 154,pp.978– 989,2022. doi.org/10.1016/j.ijplas.2022.103296.
. Maleki, E., Farrahi, G. H., Reza Kashyzadeh, K., Unal, O., Gugaliano, M., & Bagherifard, S. Effects of conventional
and severe shot peening on residual stress and fatigue strength of steel AISI 1060 and residual stress relaxation due
to fatigue loading: Experimental and numerical simulation. Metals and Materials International, vol. 27, pp. 2575-
, 2021. doi.org /10.1007/ s12540- 020-00890-8.
. Wang, Z. D., Sun, G. F., Lu, Y., Chen, M. Z., Bi, K. D., & Ni, Z. H. Microstructural characterization and mechanical
behavior of ultrasonic impact peened and laser shock peened AISI 316L stainless steel. Surface and Coatings
Technology, vol. 385, pp.1- 38, 2020. doi.org/10.1016 /j.surfcoat.2020.125403.
. Priyambodo, B. H., Nugroho, K. C., Atmoko, N. T., & Yaqin, R. I. Effect of Oil Quenching and Shot Peening to
Improve Hardness Behavior of S45C Carbon Steel. In Materials Science Forum, vol. 1067, pp. 27-33,2022. Trans
Tech Publications Ltd.
. Zhang, Q., Duan, B., Zhang, Z., Wang, J., & Si, C. Effect of ultrasonic shot peening on microstructure evolution
and corrosion resistance of selective laser melted Ti–6Al–4V alloy. Journal of Materials Research and Technology,
vol. 11, pp.1090-1099, 2021
. Sunardi, S., Randu, R., Listijorini, E., Saefuloh, I., Lusiani, R., Notonegoro, H. A., & Jannah, M. (2021). Fatigue
Characteristics of Medium Carbon Steel after Heat Treatment Using Sand as Cooling Media. INTEK: Jurnal
Penelitian, 8(2), 101-107.
. Bagherifard, S., Fernandez-Pariente, I., Ghelichi, R., & Guagliano, M. Effect of severe shot peening on
microstructure and fatigue strength of cast iron. International Journal of Fatigue, vol. 65, pp. 64-70, 2014.
. Pour-Ali, S., Kiani-Rashid, A. R., Babakhani, A., Virtanen, S., & Allieta, M.. Correlation between the surface
coverage of severe shot peening and surface microstructural evolutions in AISI 321: A TEM, FE-SEM and GI-
XRD study. Surface and Coatings Technology, vol. 334, pp. 461-470, 2018. doi.org/10.1016/j.surfcoat.
11.062.
. Pan, X., Gu, Z., Qiu, H., Feng, A., & Li, J. (2022). Study of the mechanical properties and microstructural response
with laser shock peening on 40CrMo steel. Metals, vol. 12, no.6, 2022. doi.org/10.3390/met12061034.
. Świetlicki, A., Szala, M., & Walczak, M. (2022). Effects of shot peening and cavitation peening on properties of
surface layer of metallic materials—a short review. Materials, vol. 15, no. 7, 2022, doi.org/10.3390/ma15072476
DOI: http://dx.doi.org/10.32497/jrm.v18i2.4307
Refbacks
- There are currently no refbacks.
Copyright (c) 2023 Jurnal Rekayasa Mesin
_____________________________________________________________________
| Publisher: Mechanical Engineering Department, Politeknik Negeri Semarang (Semarang State Polytechnic) |
1.png){kind=logo}
_____________________________________________________________________
This work is licensed under a License Creative Commons Attribution-NonCommercial-ShareAlike 4.0 Internasional.