PENGARUH PENAMBAHAN LIMBAH PLASTIK JENIS THERMOSETTING TERHADAP MUTU BATA RINGAN (HEBEL)
DOI:
https://doi.org/10.32497/wahanats.v25i2.2160Keywords:
plastic waste, compressive strength, lightweight brickAbstract
At this time, plastic is a material that is needed by the wider community and its impact is also extraordinary after the plastic is used in everyday life which can cause serious problems if the management is not done properly. The problem of plastic waste does not only occur in the city of Semarang, but also in other cities, so that the Ministry of Environment and Forestry to impose a program to use paid plastic bags in the short term. But this is only to deal with problems in the short term. In the long run, it will not solve the problem of "plastic waste", because the policy actually encourages people to buy plastic which, of course, will add a new burden on the community to buy it. The results showed that the compressive strength of light brick with the model / type of BN s.d. B10.0 with 10 variations of the mixture of the addition of plastic waste starting from (1.0 to 10.0)% to the weight of Portland Cement (PC) there is a decrease in the average compressive strength. The lowest was the addition of 10.0% plastic waste with an average compressive strength of 9.88 kg / cm ². The regression equation obtained Y = 0.042 X ² - 1.177 X + 18.84 with a correlation value R ² = 0.934, meaning that the addition of plastic waste ranging from (1.0 to 10.0)% of the weight of Portland Cement (PC) has the effect of "very strong "against the compressive strength. So we can get a picture that by adding the addition of plastic waste affects the compressive strength decreases. So that it can be investigated with other compositions by adding Fly Ash and sand made with a mixture ratio of 1 PC: 2 Aggregate (Sand and Fly Ash), with the hope that this Fly Ash waste can also be used for lightweight brick building elements
References
Ahmad Wancik, Ima Satyarno, Kardiyono Tjokrodimulyo, 2008, Pengaruh Styroform pada Komposit mortar;
American Society for Testing and Material; 1997;Annual Book of ASTM Standards,Vol.04.02, Concrete and Aggregates, Philadelphia : ASTM.
Anto Dajan ; 1996 , Pengantar Statistik Jilid II, Lembaga Penelitian Pendidikan dan Penerangan Ekonomi dan Sosial, Jakarta
Dedy Sumaryanto, Imam Satyarno, Kardiyono Tjokrodimulyo, 2009 Batako Sekam Padi Mortar Semen;
Departemen Permukiman dan Prasarana Wilayah, Badan Penelitian dan Pengembangan Wilayah, Badan Penelitian dan Pengembangan Kimpraswil, Standar Nasional Indonesia, 2002 , Metode, Spesifikasi dan Tata Cara Bagian 2 : Batuan Sedimen, Agregat,Departemen Kimpraswil, Jakarta
Departemen Permukiman dan Prasarana Wilayah, Badan Penelitian dan Pengembangan Wilayah, Badan Penelitian dan Pengembangan Kimpraswil, Standar Nasional Indonesia, 2002 , Metode, Spesifikasi dan Tata Cara Bagian 3 : Beton, Semen, Perkerasan Beton Semen, Departemen Kimpraswil, Jakarta
D.C. Teychene, 1982, Design of Normal Concrete Mixes, London, Departement of Environment, Building Research Establishment, Transport and Road Research Laboratory
Ghozali, Imam, 2009, Aplikasi Analisis Multivariate dengan program SPSS, Cetakan IV, Badan Penerbit Universitas Diponegoro, Semarang
Hendy Febriyatno,2012,Pemanfaatan Limbah Bahan Padat Sebagai Agregat Kasar Pada Pembuatan Beton Normal, Universitas Gundarma, Jakarta, 09 Februari 2012
Haryoshi Utami, 2011, Pengaruh Perendaman Beton PC I PT. Semen Padang dalam air laut dan air tawar terhadap sifat Kuat Tekan, FMIPA Universitas Andalas, Padang
Izzudin, Ary Setyawan, SA Kristiawan, 2014, Pengaruh Penambahan Serat Limbah Botol Plastik terhadap Karakteristik Mekanik dan susut repair Mortar;
Paul Nugraha, Antoni, 2007, Teknologi Beton, Andi Offset, Yogyakarta
Polytechnic Educational Develepment Center; 1987;Teknologi Bahan 1 , Departemen Pendidikan dan Kebudayaan, Direktorat Pendidikan Tinggi PEDC - Bandung, Bandung
Polytechnic Educational Develepment Center; 1987;Teknologi Bahan 2 , Departemen Pendidikan dan Kebudayaan, Direktorat Pendidikan Tinggi PEDC - Bandung, Bandung
Ritonga, Abdulrahman, 1987 , Statistik Terapan untuk Penelitian, Lembaga Penerbit FE-UI, Jakarta
Tjokrodimuljo K, 1996, Teknologi Beton, Naviri, Yogyakarta
Tri Mulyono, 2005, Teknologi Beton, Andi Offset, Yogyakarta
Sampah Masalah Serius Kota Semarang, 2016, http://Yulianto, 27 Mei 2016
Sampah Permukiman Masih Terbengkelai, 2016, http://Smcetak Solo Metro, 21 Mei 2016
Kebijakan Plastik Berbayar, 2016, http://Tasroh, 24 Pebruari 2016
Limbah di Sleman Didominasi Sampah Plastik, 2016, http://Amelia Hapsari, 02 Maret 2016
Penyebab Metro Banjir, Banyak Sampah Plastik Menyumbat Saluran Drainase, http://Lampost, 15 Mei 2016.
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).