Pengaruh Penambahan Limbah Plastik Jenis Thermosetting Terhadap Parameter Marshall Laston AC-WC
DOI:
https://doi.org/10.32497/wahanats.v24i2.1733Keywords:
plastic waste, concrete asphalt substitutionAbstract
At present, plastic is a material that is needed by the community at large, where the impact is also very extraordinary after the plastic is used in everyday life which can cause serious problems if the management is not done properly. The problem of plastic waste does not only occur in the city of Semarang, but also in other cities, so that the Ministry of Environment and Forestry has implemented a paid plastic bag program in the short term. But this is only to deal with problems in the short term. In the long run, it will not solve the problem of "plastic waste", because the policy actually encourages people to buy plastic which, of course, will add a new burden for the community to buy it. Based on the above problems, it is necessary to utilize this plastic waste to be made into road pavement materials such as in the manufacture of Asphal Concrette Wearing Course, by making 5 mixed variations ranging from (2 to 10)% of the weight of the aggregate . This research was initiated through a survey process, material procurement, testing of stacking materials, making test specimens, testing specimens. The results of the research can show that the type of Thermosetting plastic waste has a significant influence on the Asphalt Concrete mixture AC-WC heat mixture, including: Density, Marshall Stability, Flow, VIM, VMA, MQ and the remaining Marshall Stability tend to show an increase, moderate VFA and VIMrefusal Density values tend to show a decrease. Thus the plastic waste from the Thermosetting type can be used as a partial replacement of the aggregate for the Asphalt Concrete mixture AC-WC heat mixture with a plastic waste content is limited to a maximum of 10% and at an optimum asphalt content of 5.55%. Thus this research is expected to be of benefit to the industry and the people of Semarang in relation to the use of plastic waste for road pavement.References
AASHTO, 1998, Standard Specifications for Transfortation Materials and Methods of Sampling and Testing, Part I, Specifications, Nineteenth Edition, Washington D.C
AASHTO, 1998, Standard Specifications for Transfortation Materials and Methods of Sampling and Testing, Part II, Test, Nineteenth Edition, Washington D.C
ASTM, 2005, Annual Book of ASTM Standards, Vol.04.02, Concrete and Aggregates, Philadelphia, ASTM
ASTM, 2005, Standard Test for Road and Paving Materials. American Society for Testing and Materials International, Vol. 04 No. 03, West Conshohocken
Anita Rahmawati dan Rama Rizana, 2013, Pengaruh penggunaan limbah plastik polipropilena sebagai Pengganti agregat pada campuran laston terhadap Karakteristik Marshall, Konferensi Nasional Teknik Sipil 7 (KoNTekS 7), UNS Surakarta
Anto Dajan, 1996, Pengantar Statistik Jilid II, Lembaga Penelitian Pendidikan dan Penerangan Ekonomi dan Sosial, Jakarta
Departemen KIMPRASWIL, Badan Penelitian dan Pengembangan Wilayah, Badan Penelitian dan Pengembangan Kimpraswil, Standar Nasional Indonesia, 2002, Metode, Spesifikasi dan Tata Cara Bagian 2: Batuan Sedimen, Agregat, Departemen Kimpraswil, Jakarta
Departemen KIMPRASWIL, Badan Penelitian dan Pengembangan Wilayah, Badan Penelitian dan Pengembangan Kimpraswil, Standar Nasional Indonesia, 2002, Metode, Spesifikasi dan Tata Cara Bagian 3: Beton, Semen, Perkerasan Beton Semen, Departemen Kimpraswil, Jakarta
Departemen KIMPRASWIL, Balitbang Kimpraswil, Standar Nasional Indonesia, 2002, Metode, Spesifikasi dan Tata Cara Bagian 4: Aspal, Aspal Batu Buton (Lasbuton), Perkerasan Jalan, Departemen Kimpraswil, Jakarta
Departemen PU, Balitbang PU, 2007, Spesifikasi Campuran Beraspal Panas, Departemen Pekerjaan Umum, Jakarta
Ghozali, Imam, 2009, Aplikasi Analisis Multivariate dengan program SPSS, Cetakan IV, Badan Penerbit Universitas Diponegoro, Semarang
Harold N. Atkins, 1996, Highway Materials, Soils and Concretes, 3th Edition Prentice Hall, New Jersey
Kementerian PUPR, Direktorat Jenderal Bina Marga, 2018, Spesifikasi Umum 2018 untuk Pekerjaan Konstruksi Jalan dan Jembatan, Kementerian PUPR, Jakarta
Kennedy, T. W, 1996, The Bottom Line: Superpave System Works, The Superpave Asphalt research Program, The University of Texas at Austin
PEDC, 1987, Teknologi Bahan 1, Departemen Pendidikan dan Kebudayaan, Direktorat Pendidikan Tinggi PEDC - Bandung, Bandung
PEDC, 1987, Teknologi Bahan 3, Departemen Pendidikan dan Kebudayaan, Direktorat Pendidikan Tinggi PEDC - Bandung, Bandung
Ritonga, Abdulrahman, 1987, Statistik Terapan untuk Penelitian, Lembaga Penerbit FE-UI, Jakarta
Shell Bitumen, 1991, The Shell Bitumen Hand Book, Published By Shell Bitumen, East Molesey Serrey
Silvia Sukirman, 2003, Beton Aspal Campuran Panas, Granit, Bandung
The Asphalt Institute, 1993, Mix Design Methods for Asphalt Concrete and Other Hot-Mix Types, Manual Series No.2 (MS ”“ 2), Asphalt Institute, Lexington USA
Sampah Masalah Serius Kota Semarang, 2016, http://Yulianto, 27 Mei 2016
Sampah Permukiman Masih Terbengkelai, 2016, http://Smcetak Solo Metro, 21 Mei 2016
Kebijakan Plastik Berbayar, 2016, http://Tasroh, 24 Pebruari 2016
Limbah di Sleman Didominasi Sampah Plastik, 2016, http://Amelia Hapsari, 02 Maret 2016
Penyebab Metro Banjir, Banyak Sampah Plastik Menyumbat Saluran Drainase, 2016, http://Lampost, 15 Mei 2016
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).